t-top bag

Our storage bag is a convenient way to transport your Sea Eagle. This 26x43 inch bag will comfortably hold a deflated SE-6, SE-8, SE-9, or SE-330 and several accessories (i.e. oars, pump & motormount).
25.00 USD

This trim, attractive bag fits on the bow of our 420x, 380x & 340x kayaks. Great for storing snacks, sodas, repair kits or a spare pump.Also fits on our 395ps and 435ps paddleski models.
21.00 USD

Strong, 100% stainless steel T-top system has all the looks and function of a custom in a do-it-yourself, bolt together assembly. Durable, long-lasting canopy is framed with a welded 1" tube, and measures 60"W x 84"L. Buy the Canopy Frame and then choose from either 1/2" tube Standard Uprights or Highbar Uprights. Fits most center consoles up to around 50" wide Front V-brace system accommodates a wide range of console heights and allows mounting on either side of your windshield Standoffs and canopy covers sold separately.
1125.00 USD

Strong, 100% stainless steel T-top system has all the looks and function of a custom in a do-it-yourself, bolt together assembly. Durable, long-lasting canopy is framed with a welded 1" tube, and measures 60"W x 84"L. Buy the Canopy Frame and then choose from either 1/2" tube Standard Uprights or Highbar Uprights. Fits most center consoles up to around 50" wide Front V-brace system accommodates a wide range of console heights and allows mounting on either side of your windshield Standoffs and canopy covers sold separately.
1125.00 USD

Strong, 100% stainless steel T-top system has all the looks and function of a custom in a do-it-yourself, bolt together assembly. Durable, long-lasting canopy is framed with a welded 1" tube, and measures 60"W x 84"L. Buy the Canopy Frame and then choose from either 1/2" tube Standard Uprights or Highbar Uprights. Fits most center consoles up to around 50" wide Front V-brace system accommodates a wide range of console heights and allows mounting on either side of your windshield Standoffs and canopy covers sold separately.
1125.00 USD

T-Top & Hard-Top Boat Cover Finally, boat covers designed to fit the intricacies of T-Tops and Hard-Tops, these covers will accommodate VHF and GPS antennas, outrigger mounts, and rod holders. No detail is overlooked in these, easy-to-install covers: a double-reinforced bow area for bow pulpit and anchor roller offers extra protection and prolonged life of the cover, while custom zippered doorways on both port and starboard, side allow for easy access to and from the boat. Manufactured of tough, waterproof 6 oz. PolyGuard--a strong, lightweight, and fade resistant acrylic coated 300 Denier polyester--these covers deliver great protection against UV damage and are incredibly water repellant and mildew resistant. Covers include a Self-Adhesive Reinforcement Kit for customization, a heavy-duty boat cover Tie down,Kit, and two protective antenna sleeves. Covers will accommodate Bow Rails up to 24". For dual,Engines order next size up. Include bow pulpit and engine bracket in centerline measurement.,Color: Mist Gray. 3-year manufacturers limited warranty.
499.99 USD

Makes excellent use of the dead space underneath the wooden seat. Nylon flap secured with Velcro makes attachment easy. Comes with Nylon shoulder strap to carry to and from your boat. Storage capacity: 14 x 24 x 9.
39.00 USD

The main features of these covers are: Bow and stern sections are separated into two halves. The sections are joined through the use of a 7mm single pull molded nylon zipper on both the port and starboard sides. The stitching of the zippers into the cover halves feature beginning each zipper at the top of the console tube and ending at the hem (finished outside edge). This allows installation of the cover by a single person inside the boat. The "console tube" or center portion of the cover fits over the console and under the T-top. Cover design incorporates a "console tube" section with two adjustable straps which lift and secure the cover halves up and over the console body and up under the T-top. The top edge of console tube incorporates an adjustable draw rope in both front and rear sections. The draw ropes tighten the tube from side to side around the T-top verticals and also are used to secure the tube to the upper horizontal supports of the T-top. The "console tube" is not a perfect rectangle as it comes up off the cover halves. Rather it is more trapezoidal in shape and wider at the base than at the top. This feature allows these covers to fit and function properly even though there are variations in size and position of the T-tops within the confines of the hull and deck. Tie-down system in the hem or perimeter of the covers. To relieve stress on the zippered ends during over the road trailering we have added a webbing strap and quick release buckle to the cover at both sides just above the zipper to facilitate the installation of the cover by a single person. The rope that spans the perimeter of the cover is made into two sections; the first goes from one side at the zipper opening, around the bow to the same point on the opposite side. The second goes around the stern of the boat in a similar fashion. Max. Beam Width: 102"
309.99 USD

The main features of these covers are: Bow and stern sections are separated into two halves. The sections are joined through the use of a 7mm single pull molded nylon zipper on both the port and starboard sides. The stitching of the zippers into the cover halves feature beginning each zipper at the top of the console tube and ending at the hem (finished outside edge). This allows installation of the cover by a single person inside the boat. The "console tube" or center portion of the cover fits over the console and under the T-top. Cover design incorporates a "console tube" section with two adjustable straps which lift and secure the cover halves up and over the console body and up under the T-top. The top edge of console tube incorporates an adjustable draw rope in both front and rear sections. The draw ropes tighten the tube from side to side around the T-top verticals and also are used to secure the tube to the upper horizontal supports of the T-top. The "console tube" is not a perfect rectangle as it comes up off the cover halves. Rather it is more trapezoidal in shape and wider at the base than at the top. This feature allows these covers to fit and function properly even though there are variations in size and position of the T-tops within the confines of the hull and deck. Tie-down system in the hem or perimeter of the covers. To relieve stress on the zippered ends during over the road trailering we have added a webbing strap and quick release buckle to the cover at both sides just above the zipper to facilitate the installation of the cover by a single person. The rope that spans the perimeter of the cover is made into two sections; the first goes from one side at the zipper opening, around the bow to the same point on the opposite side. The second goes around the stern of the boat in a similar fashion. Max. Beam Width: 102"
464.99 USD

The main features of these covers are: Bow and stern sections are separated into two halves. The sections are joined through the use of a 7mm single pull molded nylon zipper on both the port and starboard sides. The stitching of the zippers into the cover halves feature beginning each zipper at the top of the console tube and ending at the hem (finished outside edge). This allows installation of the cover by a single person inside the boat. The "console tube" or center portion of the cover fits over the console and under the T-top. Cover design incorporates a "console tube" section with two adjustable straps which lift and secure the cover halves up and over the console body and up under the T-top. The top edge of console tube incorporates an adjustable draw rope in both front and rear sections. The draw ropes tighten the tube from side to side around the T-top verticals and also are used to secure the tube to the upper horizontal supports of the T-top. The "console tube" is not a perfect rectangle as it comes up off the cover halves. Rather it is more trapezoidal in shape and wider at the base than at the top. This feature allows these covers to fit and function properly even though there are variations in size and position of the T-tops within the confines of the hull and deck. Tie-down system in the hem or perimeter of the covers. To relieve stress on the zippered ends during over the road trailering we have added a webbing strap and quick release buckle to the cover at both sides just above the zipper to facilitate the installation of the cover by a single person. The rope that spans the perimeter of the cover is made into two sections; the first goes from one side at the zipper opening, around the bow to the same point on the opposite side. The second goes around the stern of the boat in a similar fashion. Max. Beam Width: 102"
329.99 USD