dock line holder

Snapper II Line Holder Black The Snappers can put order to any boat. The holder's simple locking mechanism allows for instant locking and unlocking of the line holding retaining strap. The Snapper II can either be screwed or through-bolted in to place (hardware not included) and can hold up to 50 feet of 1/2 in. line. They make excellent holders for halyard lines, dock lines, and sheet lines.
4.89 USD

Bungee Dock Line 4Ft Airhead Bungee Dock Lines absorb shock to boats, cleats, docks, pylons and other hardware. The bungee cord is hidden inside the rope and acts as a built-in snubber. Two foam floats protect the boat from chafing. There's a sliding adjustment at both ends for quick docking. Recommended for docking boats and PWC's up to 4,000 pounds. Tensile strength is 2,150 pounds. Black/Blue/Red color scheme.
9.99 USD

Bungee Dock Line 6Ft Airhead Bungee Dock Lines absorb shock to boats, cleats, docks, pylons and other hardware. The bungee cord is hidden inside the rope and acts as a built-in snubber. Two foam floats protect the boat from chafing. There's a sliding adjustment at both ends for quick docking. Recommended for docking boats and PWC's up to 4,000 pounds. Tensile strength is 2,150 pounds. Black/Blue/Red color scheme.
12.99 USD

Bungee Dock Line Airhead Bungee Dock Lines absorb shock to boats, cleats, docks, pylons and other hardware. The bungee cord is hidden inside the rope and acts as a built-in snubber. Two foam floats protect the boat from chafing. There's a sliding adjustment at both ends for quick docking. Recommended for docking boats and PWC's up to 4,000 pounds. Tensile strength is 2,150 pounds. Black/Blue/Red color scheme.
9.99 USD

Bungee Dock Line 5Ft Airhead Bungee Dock Lines absorb shock to boats, cleats, docks, pylons and other hardware. The bungee cord is hidden inside the rope and acts as a built-in snubber. Two foam floats protect the boat from chafing. There's a sliding adjustment at both ends for quick docking. Recommended for docking boats and PWC's up to 4,000 pounds. Tensile strength is 2,150 pounds. Black/Blue/Red color scheme.
11.99 USD

We offer a complete line of rugged dock hardware for building a dock at your summer cabin or waterfront home. Designed primarily for noncommercial users, it s sturdy enough for boat yards and smaller marinas. To help get you started, we offer a Planning Kit (See facing page) that s filled with details about dock design and construction. Once you have a plan and materials list, we ll supply the hardware and your local lumber yard can provide the wood. For ideas on constructing your own dock, taek a look at detailed plans at http://www.tiedown.com/pdf/a936-3.pdf Several sizes of float drums are available, please search under Model 140264 A. Inside Corner Used in combination with Outside Corner (E) to connect side and cross stringers on end of dock section. Includes welded gusset for dock framing. Requires eight 3/8" carriage bolt sets. H. Washer Plate Used with cross stringers to back up Angle Braces (C) or Pipe Holders (I). Two carriage bolt holes. B. Backup Plates 5" x 5" reinforcing plates are used to back up the Single T Males (F) and Females (G). I. 3"O.D. Pipe Holder Allows dock to ride up and down on anchoring pipe. Bolts to the outside of a side stringer and accepts up to 2"I.D. pipe. Uses two Washer Plates (H) for backing. Requires four 3/8" carriage bolt sets. C. Galvanized Stringer Angle Used to attach cross stringers to side stringers, and is backed up by Washer Plates (H). Requires four 3/8" carriage bolt sets. J. Outside Corner, Female This is identical to the Outside Corner End, except it has two 1/2" tabs which connect to a Male Outside Corner (K) to create a flexible joint between dock sections. No additional bolts required if used with an Inside Corner. D. Inside Corner with 2" Pipe Holder For 3" Pipe Model 542910 This inside corner allows you to use pipe at each corner for anchoring. Dock will float up and down if water level changes. Used in combination with outside corners (E). Requires eight 3/8" carriage-bolt sets. K. Outside Corner, Male This is identical to the Outside Corner End, except it has a single 1/2" tab which connects to a Female Outside Corner (J) to create a flexible joint between dock sections. Does not require additional bolts if used with an inside corner. E. Outside Corner End Used with Inside Corner to connect side stringers to end stringers, resulting in an absolutely square corner that won t come apart. No additional bolts required if used with Inside Corner (A). L. Piling Hoop & Roller Assembly Intended for areas with lots of wind, current, or tidal action. Combines the Piling Hoop (N) and Roller Assembly (M) to make up-and-down movement easier. For pilings up to 12"dia. F. Single T, Male Used to connect finger dock to main walkway, and to attach dock sections to sea walls. Single 1/2" tab connects to Female Single T (G) or female Outside Corner (J) to allow articulation. Four bolt holes. M. Heavy Duty Roller Assembly Bracket and roller bolt directly to the Deck Plate (L) and can be added to aid up-and-
49.99 USD

We offer a complete line of rugged dock hardware for building a dock at your summer cabin or waterfront home. Designed primarily for noncommercial users, it s sturdy enough for boat yards and smaller marinas. To help get you started, we offer a Planning Kit (See facing page) that s filled with details about dock design and construction. Once you have a plan and materials list, we ll supply the hardware and your local lumber yard can provide the wood. For ideas on constructing your own dock, taek a look at detailed plans at http://www.tiedown.com/pdf/a936-3.pdf Several sizes of float drums are available, please search under Model 140264 A. Inside Corner Used in combination with Outside Corner (E) to connect side and cross stringers on end of dock section. Includes welded gusset for dock framing. Requires eight 3/8" carriage bolt sets. H. Washer Plate Used with cross stringers to back up Angle Braces (C) or Pipe Holders (I). Two carriage bolt holes. B. Backup Plates 5" x 5" reinforcing plates are used to back up the Single T Males (F) and Females (G). I. 3"O.D. Pipe Holder Allows dock to ride up and down on anchoring pipe. Bolts to the outside of a side stringer and accepts up to 2"I.D. pipe. Uses two Washer Plates (H) for backing. Requires four 3/8" carriage bolt sets. C. Galvanized Stringer Angle Used to attach cross stringers to side stringers, and is backed up by Washer Plates (H). Requires four 3/8" carriage bolt sets. J. Outside Corner, Female This is identical to the Outside Corner End, except it has two 1/2" tabs which connect to a Male Outside Corner (K) to create a flexible joint between dock sections. No additional bolts required if used with an Inside Corner. D. Inside Corner with 2" Pipe Holder For 3" Pipe Model 542910 This inside corner allows you to use pipe at each corner for anchoring. Dock will float up and down if water level changes. Used in combination with outside corners (E). Requires eight 3/8" carriage-bolt sets. K. Outside Corner, Male This is identical to the Outside Corner End, except it has a single 1/2" tab which connects to a Female Outside Corner (J) to create a flexible joint between dock sections. Does not require additional bolts if used with an inside corner. E. Outside Corner End Used with Inside Corner to connect side stringers to end stringers, resulting in an absolutely square corner that won t come apart. No additional bolts required if used with Inside Corner (A). L. Piling Hoop & Roller Assembly Intended for areas with lots of wind, current, or tidal action. Combines the Piling Hoop (N) and Roller Assembly (M) to make up-and-down movement easier. For pilings up to 12"dia. F. Single T, Male Used to connect finger dock to main walkway, and to attach dock sections to sea walls. Single 1/2" tab connects to Female Single T (G) or female Outside Corner (J) to allow articulation. Four bolt holes. M. Heavy Duty Roller Assembly Bracket and roller bolt directly to the Deck Plate (L) and can be added to aid up-and-
54.99 USD

We offer a complete line of rugged dock hardware for building a dock at your summer cabin or waterfront home. Designed primarily for noncommercial users, it s sturdy enough for boat yards and smaller marinas. To help get you started, we offer a Planning Kit (See facing page) that s filled with details about dock design and construction. Once you have a plan and materials list, we ll supply the hardware and your local lumber yard can provide the wood. For ideas on constructing your own dock, taek a look at detailed plans at http://www.tiedown.com/pdf/a936-3.pdf Several sizes of float drums are available, please search under Model 140264 A. Inside Corner Used in combination with Outside Corner (E) to connect side and cross stringers on end of dock section. Includes welded gusset for dock framing. Requires eight 3/8" carriage bolt sets. H. Washer Plate Used with cross stringers to back up Angle Braces (C) or Pipe Holders (I). Two carriage bolt holes. B. Backup Plates 5" x 5" reinforcing plates are used to back up the Single T Males (F) and Females (G). I. 3"O.D. Pipe Holder Allows dock to ride up and down on anchoring pipe. Bolts to the outside of a side stringer and accepts up to 2"I.D. pipe. Uses two Washer Plates (H) for backing. Requires four 3/8" carriage bolt sets. C. Galvanized Stringer Angle Used to attach cross stringers to side stringers, and is backed up by Washer Plates (H). Requires four 3/8" carriage bolt sets. J. Outside Corner, Female This is identical to the Outside Corner End, except it has two 1/2" tabs which connect to a Male Outside Corner (K) to create a flexible joint between dock sections. No additional bolts required if used with an Inside Corner. D. Inside Corner with 2" Pipe Holder For 3" Pipe Model 542910 This inside corner allows you to use pipe at each corner for anchoring. Dock will float up and down if water level changes. Used in combination with outside corners (E). Requires eight 3/8" carriage-bolt sets. K. Outside Corner, Male This is identical to the Outside Corner End, except it has a single 1/2" tab which connects to a Female Outside Corner (J) to create a flexible joint between dock sections. Does not require additional bolts if used with an inside corner. E. Outside Corner End Used with Inside Corner to connect side stringers to end stringers, resulting in an absolutely square corner that won t come apart. No additional bolts required if used with Inside Corner (A). L. Piling Hoop & Roller Assembly Intended for areas with lots of wind, current, or tidal action. Combines the Piling Hoop (N) and Roller Assembly (M) to make up-and-down movement easier. For pilings up to 12"dia. F. Single T, Male Used to connect finger dock to main walkway, and to attach dock sections to sea walls. Single 1/2" tab connects to Female Single T (G) or female Outside Corner (J) to allow articulation. Four bolt holes. M. Heavy Duty Roller Assembly Bracket and roller bolt directly to the Deck Plate (L) and can be added to aid up-and-
59.99 USD

Use it to easily loop your dock lines around posts or pilings. Especially useful at low tide when the piling is too high to reach. Mounts to any boat pole UV-resistant plastic
11.99 USD

Line Holder A piling mounted line holder made of durable high density polyethylene. This product requires no maintenance, is easy to install and compliments any maritime setting. Sold in pairs.
19.99 USD