hand pump holding tanks

Electric Galley Pump & Faucet This attractive faucet and pump combination is the economical answer to running water at the turn of a switch. The quiet operation electric pump is compact, easy to install, and works with both fresh and salt water. The faucet has a stainless steel swing spout, easy-to-clean white plastic base, and built-in switch to operate the pump. The centrifugal pump may be screwed directly into a water tank.
62.99 USD

Bilge Pump Rule's completely submersible, non-automatic bilge pumps offer good performance at a value price. Designed to be installed in conjunction with a float switch or panel switch, these pumps feature easy clean snap-lock strainer bases, silent, vibrationless operation, anti-airlock protection, stainless steel shafts, and no burn-out when run dry. 12VDC.
34.99 USD

Replacement Pump Cartridge The SHURflo Piranha cartridge is simple and easy to change. Quiet and tough these cartridges are designed specifically to handle continuous duty expected from your livewell/aerator pump.
19.99 USD

Bilge Pump Id Pl-2 Plastic ID plates are molded in black plastic with white letters abs bevel.
1.39 USD

Aerator Pump 500 Pumps 500 GPH at open flow, up to 325 GPH at 3 foot head. Ideal for small boats or boats with single, standard-capacity livewells. 1-1/2" inlet for recirculation pump. 12-volt D.C., CE rated. The threaded outlet on this aerator pump can be converted for hose connection. Use one of the Thread-to-Barb connectors (included with aftermarket pump) or Flow-Rite Qwik-Lok couplers.
37.99 USD

Automatic Bilge Pump Rule Rule-Mate Series Fully Automatic Pumps contain the pump and the non-mercury float switch in a single, compact housing. As the water level rises, so does the float switch, activating the pump when the water level reaches 2-1/8''. There is no on/off cycling and therefore, no power use until the pump comes on. Features include easy clean snap-lock strainer bases, silent, vibrationless operation, anti-airlock protection, stainless steel shafts, and no burn-out when run dry. 12VDC.
149.99 USD

Todd Polyethylene Water Tanks These USCG-approved tanks are manufactured from FDA-approved polyethylene. Fitting Kits (not included) enable you to customize port locations. Threaded NPT ports are molded in to eliminate stress cracks and leaking, and include: 1 1/2" fill 1/2" vent 1/2" supply port Note: No plumbing fittings supplied
129.99 USD

Plastimo Flexible Water Tanks Flexible, light and form-fitting, these tanks use a PVC bladder inside a tough, abrasion-resistant nylon outer envelope. Maintenance is easy because the inner bladder can be removed for cleaning and inspection. The bladder is slightly oversized so pressure is exerted on its sides, rather than on the seams. 1 1/2" 90 Fill Fitting 1/2" Straight Outlet Fitting Fitings Ready to Install Heat Welded Seams
134.99 USD

Plastimo Flexible Water Tanks Flexible, light and form-fitting, these tanks use a PVC bladder inside a tough, abrasion-resistant nylon outer envelope. Maintenance is easy because the inner bladder can be removed for cleaning and inspection. The bladder is slightly oversized so pressure is exerted on its sides, rather than on the seams. 1 1/2" 90 Fill Fitting 1/2" Straight Outlet Fitting Fitings Ready to Install Heat Welded Seams
167.99 USD

Plastimo Flexible Water Tanks Flexible, light and form-fitting, these tanks use a PVC bladder inside a tough, abrasion-resistant nylon outer envelope. Maintenance is easy because the inner bladder can be removed for cleaning and inspection. The bladder is slightly oversized so pressure is exerted on its sides, rather than on the seams. 1 1/2" 90 Fill Fitting 1/2" Straight Outlet Fitting Fitings Ready to Install Heat Welded Seams
147.99 USD