rail mount outboard

Kettle Rail Mount Bracket The round rail, quick-disconnect, all angle mounting bracket is made entirely of 18-8 stainless steel and 356 anodized aluminum to endure the most severe marine environment. Fits any angle railing and detaches quickly for storage without tools, leaving no hardware on the rail.
53.99 USD

Includes one stainless wrap around rail and one underside support rail that are reversible. Stainless steel construction with poly comfort steps. For use on outboard transoms Mounts on 10 degree angle on transom slides vertically up under platform for stowage
219.99 USD

225 Economy Ratchet Rail Mount Reinforced UV protected white nylon ratchet rail mount that fits 7/8'' and 1'' rails. Standard 1''-14 thread with a hole cut for cable feed.
11.99 USD

245 GPS Antenna Rail Mount Reinforced UV protected white nylon rail mount for GPS antennas. Fits 7/8'' and 1'' rails. Standard 1''-14 thread with a hole cut for cable feed.
9.99 USD

Round Rail Mount Lever with Washer Replacement Parts for Magma grillsMagma Part #:10-043
9.49 USD

Bulkhead Rail Mount Table Mount This all 18-8 stainless steel mount attaches to any vertical flat surface such as bulkheads, hulls, transoms or cabin sides. Also mounts to square and flat rails. Fits HORIZONTAL RAILS up to 2-1/4" (57 mm) high by any depth or VERTICAL RAILS up to 1-5/8" (41 mm) wide by any depth. Some fasteners required for installation.
49.99 USD

Inboard/Outboard Swim Platform White Works on boats with inboards and boats with outboards. Single step folds down for easy boarding, and then up out of the way when not in use. Stainless grab rail provides a place to steady yourself, and support for the platform. I/O1 Step/13''18''W x 15 1/2'' D x 1 1/2'' T. Sh. Wt. 8 lbs.
136.99 USD

Shakespeare's Style 4720 Economy Rail Mount is designed for quick and easy installation on vertical or horizontal, straight or angled rails. Its simple design makes installation a snap. The vice section grips the rail, and the flat section supports the antenna. The flat section can also be bolted to a flat surface, instead of to the rail grip. Standard 1" - 14 thread Nylon adapters included for 7/8", 1", and 1 " vertical or horizontal rails Stainless steel construction
22.99 USD

Precise steering control for high-speed outboard boats SeaStar PRO outboard steering systems are the choice for high speed single-engine outboard boats, like bass, flats, combo race/ski and other performance boats with speeds above 65mph. Recommended for single non-power-assisted outboards up to 300hp. SeaStar PRO has steered the Bass Masters Classic since 1994. The easy-to-install Sea Star PRO kit is built using the same components used in factory boatbuilding. The kit includes a 2.0 PRO HH5770 helm, semi-universal front mount HC5345 cylinder, two quarts of oil and an installation guide. Kit can be used with jackplates (allow enough hose length for full steering motion and no interference during trim and tilt) and performance props. Compact helm has a 4 7/16" footprint and requires only a 3" cutout. Match the helm with Kevlar reinforced HO57XX hoses. Meets ABYC standards and NMMA requirements. Horsepower: Single engine 300hp; dual engine 600hp Speed: 60mph + Helm: 2.0 cu.ft. capacity Hose: Kevlar reinforced, 1500PSI Turns Lock-to-Lock: 4.25 Included equipment: Helm pump, cylinder, bleeder kit. Hoses sold separately. (Uses HO57XX series) Steering Wheel: Not included Steering Wheel Shaft: 3/4" tapered Warranty: Two years
1039.00 USD

Hydraulic steering for outboards to 150hpControlling large outboards with mechanical steering may require lots of effort. On the other hand, traditional hydraulic systems may be more than is needed on lower horsepower engines. BayStar brings safety, reliability and comfort of hydraulic steering to outboard powered boats like inflatable RIBs and runabouts with a maximum 150 HP (total) or less. The super low friction helm pump provides smooth comfortable steering. The balanced cylinder features a compact design that easily fits most splashwells 23" or less. BayStar Kits come complete with everything needed for an install. The cylinder utilizes the factory outboard engine supplied drag link for simplified installation. For your convenience two lengths of 20' cut to fit tubing are supplied (2 x 20' length). Kit includes Helm Pump, Cylinder, Tubing Kit, two bottles of hydraulic steering fluid and one fill tube for easy fill and purge. Boat Type: Single station, single engine boat with outboard up to 150HP. Not for lower-horsepower outboards that use wing nut type transom mount clamping screws Compact helm has only a 5" footprint, and requires only a 3" dash cutout. 4.5 turns lock to lock. Steering Wheel: Not included. Steering Wheel Shaft: 3/4" tapered Included Equipment: Helm pump HH4016, cylinder HC4645H, tubing kit (includes two 20' cut-to-fit hoses), filler kit and two bottles of hydraulic fluid Splashwell: 5"H x 6"D x 21"W minimum Warranty: Two years
749.00 USD