rail mount outboard

Precise steering control for high-speed outboard boats SeaStar PRO outboard steering systems are the choice for high speed single-engine outboard boats, like bass, flats, combo race/ski and other performance boats with speeds above 65mph. Recommended for single non-power-assisted outboards up to 300hp. SeaStar PRO has steered the Bass Masters Classic since 1994. The easy-to-install Sea Star PRO kit is built using the same components used in factory boatbuilding. The kit includes a 2.0 PRO HH5770 helm, semi-universal front mount HC5345 cylinder, two quarts of oil and an installation guide. Kit can be used with jackplates (allow enough hose length for full steering motion and no interference during trim and tilt) and performance props. Compact helm has a 4 7/16" footprint and requires only a 3" cutout. Match the helm with Kevlar reinforced HO57XX hoses. Meets ABYC standards and NMMA requirements. Horsepower: Single engine 300hp; dual engine 600hp Speed: 60mph + Helm: 2.0 cu.ft. capacity Hose: Kevlar reinforced, 1500PSI Turns Lock-to-Lock: 4.25 Included equipment: Helm pump, cylinder, bleeder kit. Hoses sold separately. (Uses HO57XX series) Steering Wheel: Not included Steering Wheel Shaft: 3/4" tapered Warranty: Two years
274.99 USD

Stow your anchor up off the deck, ready for instant deployment. These brackets hold fluke-style Danforth, West Marine, U.S. anchors up to 35lb. and all Fortress anchors (except those with mud palms). All-stainless construction Mounts on 7/8" or 1" rails Hardware included Lifetime warranty
44.99 USD

Stow your anchor up off the deck, ready for instant deployment. These brackets hold fluke-style Danforth, West Marine, U.S. anchors up to 35lb. and all Fortress anchors (except those with mud palms). All-stainless construction Mounts on 7/8" or 1" rails Hardware included Lifetime warranty
44.99 USD

Clamp-On Rail-Mount Rod Holders - Vertical Beautiful tulip-style holders that clamp securely to your tower, hardtop or radar arch. Made from marine-grade aluminum Protected by an anodized finish in gold or silver Made in schedule pipe sizes, (use approximate pipe OD if unsure of the schedule size)
82.99 USD

Clamp-On Rail-Mount Rod Holders - Vertical Beautiful tulip-style holders that clamp securely to your tower, hardtop or radar arch. Made from marine-grade aluminum Protected by an anodized finish in gold or silver Made in schedule pipe sizes, (use approximate pipe OD if unsure of the schedule size)
82.99 USD

Clamp-On Rail-Mount Rod Holders - Vertical Beautiful tulip-style holders that clamp securely to your tower, hardtop or radar arch. Made from marine-grade aluminum Protected by an anodized finish in gold or silver Made in schedule pipe sizes, (use approximate pipe OD if unsure of the schedule size)
82.99 USD

Dual-Mount Table Mounts. 6" & 12" Table Height Extension Sets for use with T10-525/520 (models 474827 & 447805) deck socket mount kits Use Barbecue Swing Arm Mount only with 525/520 deck socket mount kits (models 474827 & 447805), Note: height extension set cannot be used with this kit Surface mount Deck Aocket kit, Locking Surface Deck Socket Mount & Flush Deck Socket Mount Kit has a shim kit included
62.99 USD

T304 stainless steel socket Adjusts to any angle to fit 7/8" to 1-1/4" vertical stanchions and horizontal rails. Fits 3/4 - 7/8" flag poles. Model 968. Mfr.'s one year limited warranty.
21.99 USD

Extra deck brackets for assorted Scotty downriggers.
59.99 USD

Handlebar/Rail Mount Bracket f/GPSII and III series Handheld GPS Units Snap your GPS unit into this secure handlebar mount and it's ready to ride. Mount fits up to a one-inch diameter bar and is perfect for your bike, motorcycle or PWC. Includes hardware and instructions.
24.99 USD