rub rail

Dual Horizontal Round Rail Mount - Choose Round Rail Size These incredibly strong rail mounts have a unique pivoting design which allows them to mount to straight or curved rail or across the corner of a stern rail. Made of 18-8 stainless steel and 356 anodized aluminum, they instantly detach without tools for compact storage.
64.99 USD

Side Mount/Square Rail BBQ Mount The accessory allow a ''Marine Kettle'' product to be mounted on a square side rail.
56.99 USD

Piling Armour Rub Strip - 5 Pack The Deep Blue Piling Armor Rub Strips are esstential for protecting the dock and pilings from your boat. It has a non- marking slick surface so it won't mark the hull. Beveled edges and counterbored mounting holes for a clean installation. Made from a U.V. stable marine-grade polymar.
39.99 USD

Rub Strake - 3/4'' Stainless x 12'' Length Sturdy and solid to withstand the harsh marine environment and afford the maximum in protection. This hollow back rub strake is constructed using highly polished type 304 stainless steel and are completely resistant to sun and salt damage. Useful on any location prone to chafe or wear. Countersunk and pre-drilled.
14.99 USD

Use with Aqua Signal Series 25 Navigation Lights, these rail brackets are easy to install. Shipping weight: 0.5
33.99 USD

Fender hanger for vertical rails. Made of tough nylon. Attaches to rail with 2 screws. Grips fender line with HD teeth
15.99 USD

Polished Stainless Elliptical Rail TACO mirror finish, Polished Marine Grade 316 Stainless Steel. Includes all threaded bolts, nuts, and washers. Non corrosive, low profile, ergonomically designed. Ideal for interior or exterior.
59.99 USD

225 Economy Ratchet Rail Mount Reinforced UV protected white nylon ratchet rail mount that fits 7/8'' and 1'' rails. Standard 1''-14 thread with a hole cut for cable feed.
11.99 USD

245 GPS Antenna Rail Mount Reinforced UV protected white nylon rail mount for GPS antennas. Fits 7/8'' and 1'' rails. Standard 1''-14 thread with a hole cut for cable feed.
9.99 USD

Nautilus Rail Chocks On-deck or on-dock small boat storage is typically handled by expensive, custom-made boat cradles or dinghy davits. Buck Woodcraft offers a simple boat storage unit made up of strong, durable rail dinghy chocks that easily adapt to a variety of small-boat hull forms: RIB dinghies, rowing skiffs, jet skis and other personal watercraft. Fabricated out of King Starboard - a marine-grade polymer that has a life expectancy that matches or exceeds fiberglass these chocks never need painting or refinishing, resist most stains, won't chip or corrode, and won't chip or scratch fiberglass hulls. Nautilus Rail Chocks and bases are 1-1/2'' thick, and all edges are rounded and milled smooth. Rails measure approximately 5''W x 4'L, and each rail is supported by two bases, each measuring approximately 6''H x 10-1/2''W. The finished structure weighs less than 30 lbs., yet is extremely strong and will easily support the weight of just about any PWC, RIB dinghy or other small to medium-size tender. Nautilus Rail Chocks are designed to pivot on their bases up to 20 degrees from vertical, so your small-craft hull will sit flush against the full width of the rails' edges along their entire length. Once you've determined the correct rail angle for your hull by placing it on the chocks, drill pilot holes through the rails into each base and lock them together with the included stainless steel screws. (Correct drill bit also included). If you ever get a different dinghy, just remove the screws and repeat the process for your new hull. It's that simple! Nautilus Rail Chock bases are pre-drilled to help simplify through-deck installation. Although Nautilus Rail Chocks are very strong, they are not designed or intended as tie-down points for your dinghy or other small boat.
499.99 USD