vacuum Mount

Metal Bulkhead Mount For 12 A/LD Signal Kit Keep your flare kit handy. Mount the Orion 12 gauge Alert/Locate deluxe kit to a bulkhead, or most any surface with this handy metal bulkhead mount.
4.79 USD

Vacuum bagging is a clamping system used for laminating a wide range of fabrics, core materials and veneers. It offers many advantages over conventional clamping. For repairs and composite construction, it uses atmospheric pressure to deliver firm even clamping pressure over the entire surface area, regardless of the type or quantity of material being laminated. By laminating over simple molds, composites can be molded into a wide range of functional shapes. #879 Release Fabric Economical Release Fabric is a tough, finely woven nylon fabric treated with a release agent. It is used to separate the absorber, breather and vacuum bag from the laminate in vacuum bagging operations. Excess epoxy bleeds through and is peeled from the cured laminate along with the Release Fabric. It's also used in hand lay-up applications to allow more squeegee pressure and protect the lay-up from contamination. Peels easily and leaves a smooth textured surface, ready for bonding or finishing. Not recommended for post-cure temperatures over 120 F (49 C). Available in 60" wide x 2 yd., and 10 yd. rolls; also in 60" x 9" sheets. #881 Breather Fabric Breather Fabric is a lightweight, polyester blanket that provides excellent air passage within the vacuum envelope while it absorbs excess epoxy. Available in 45" wide x 2.7 yd., and 10 yd. rolls. #882 Vacuum Bag Film Clear, heat-stabilized, modified nylon resin film. Can be used at temperatures up to 350 F (176 C) for typical composite cure cycle times. A tough, stretchable film for high vacuum pressures. Available in 60" wide x 2 yd., and 20 yd. rolls. #883 Vacuum Bag Sealant Mastic tape sealant for airtight seals between vacuum bags and molds. Easy to work around difficult angles, patching small leaks in the vacuum system. Available in 1/2" wide x 25' roll. #885 Vacuum Bagging Kit A complete starter kit for room temperature repairs and small laminating projects up to 13 square feet. The kit includes: 32-page manual on ''Advanced Vacuum Bagging Techniques.'' Instructions. Venturi vacuum generator. Vacuum cups. 1/4'' I.D. vacuum tubing (10'). Vacuum gauge. Junction ''T'' barbs (2). Release fabric (15 sq. ft.). Breather fabric (15 sq. ft.). Vacuum bag film (15 sq. ft.). Vacuum bag sealant (25 sq. ft.). The venturi generator develops over 20 inches Hg (mercury) of vacuum (10 psi). It is designed to run off of conventional shop air compressors delivering at least 65 psi at 3.5 SCFM. At 0 inches Hg it will evacuate 2.2 SCFM. The operating range is 40 psi - 100 psi.
75.49 USD

Vacuum bagging is a clamping system used for laminating a wide range of fabrics, core materials and veneers. It offers many advantages over conventional clamping. For repairs and composite construction, it uses atmospheric pressure to deliver firm even clamping pressure over the entire surface area, regardless of the type or quantity of material being laminated. By laminating over simple molds, composites can be molded into a wide range of functional shapes. #879 Release Fabric Economical Release Fabric is a tough, finely woven nylon fabric treated with a release agent. It is used to separate the absorber, breather and vacuum bag from the laminate in vacuum bagging operations. Excess epoxy bleeds through and is peeled from the cured laminate along with the Release Fabric. It's also used in hand lay-up applications to allow more squeegee pressure and protect the lay-up from contamination. Peels easily and leaves a smooth textured surface, ready for bonding or finishing. Not recommended for post-cure temperatures over 120 F (49 C). Available in 60" wide x 2 yd., and 10 yd. rolls; also in 60" x 9" sheets. #881 Breather Fabric Breather Fabric is a lightweight, polyester blanket that provides excellent air passage within the vacuum envelope while it absorbs excess epoxy. Available in 45" wide x 2.7 yd., and 10 yd. rolls. #882 Vacuum Bag Film Clear, heat-stabilized, modified nylon resin film. Can be used at temperatures up to 350 F (176 C) for typical composite cure cycle times. A tough, stretchable film for high vacuum pressures. Available in 60" wide x 2 yd., and 20 yd. rolls. #883 Vacuum Bag Sealant Mastic tape sealant for airtight seals between vacuum bags and molds. Easy to work around difficult angles, patching small leaks in the vacuum system. Available in 1/2" wide x 25' roll. #885 Vacuum Bagging Kit A complete starter kit for room temperature repairs and small laminating projects up to 13 square feet. The kit includes: 32-page manual on ''Advanced Vacuum Bagging Techniques.'' Instructions. Venturi vacuum generator. Vacuum cups. 1/4'' I.D. vacuum tubing (10'). Vacuum gauge. Junction ''T'' barbs (2). Release fabric (15 sq. ft.). Breather fabric (15 sq. ft.). Vacuum bag film (15 sq. ft.). Vacuum bag sealant (25 sq. ft.). The venturi generator develops over 20 inches Hg (mercury) of vacuum (10 psi). It is designed to run off of conventional shop air compressors delivering at least 65 psi at 3.5 SCFM. At 0 inches Hg it will evacuate 2.2 SCFM. The operating range is 40 psi - 100 psi.
9.49 USD

Vacuum bagging is a clamping system used for laminating a wide range of fabrics, core materials and veneers. It offers many advantages over conventional clamping. For repairs and composite construction, it uses atmospheric pressure to deliver firm even clamping pressure over the entire surface area, regardless of the type or quantity of material being laminated. By laminating over simple molds, composites can be molded into a wide range of functional shapes. #879 Release Fabric Economical Release Fabric is a tough, finely woven nylon fabric treated with a release agent. It is used to separate the absorber, breather and vacuum bag from the laminate in vacuum bagging operations. Excess epoxy bleeds through and is peeled from the cured laminate along with the Release Fabric. It's also used in hand lay-up applications to allow more squeegee pressure and protect the lay-up from contamination. Peels easily and leaves a smooth textured surface, ready for bonding or finishing. Not recommended for post-cure temperatures over 120 F (49 C). Available in 60" wide x 2 yd., and 10 yd. rolls; also in 60" x 9" sheets. #881 Breather Fabric Breather Fabric is a lightweight, polyester blanket that provides excellent air passage within the vacuum envelope while it absorbs excess epoxy. Available in 45" wide x 2.7 yd., and 10 yd. rolls. #882 Vacuum Bag Film Clear, heat-stabilized, modified nylon resin film. Can be used at temperatures up to 350 F (176 C) for typical composite cure cycle times. A tough, stretchable film for high vacuum pressures. Available in 60" wide x 2 yd., and 20 yd. rolls. #883 Vacuum Bag Sealant Mastic tape sealant for airtight seals between vacuum bags and molds. Easy to work around difficult angles, patching small leaks in the vacuum system. Available in 1/2" wide x 25' roll. #885 Vacuum Bagging Kit A complete starter kit for room temperature repairs and small laminating projects up to 13 square feet. The kit includes: 32-page manual on ''Advanced Vacuum Bagging Techniques.'' Instructions. Venturi vacuum generator. Vacuum cups. 1/4'' I.D. vacuum tubing (10'). Vacuum gauge. Junction ''T'' barbs (2). Release fabric (15 sq. ft.). Breather fabric (15 sq. ft.). Vacuum bag film (15 sq. ft.). Vacuum bag sealant (25 sq. ft.). The venturi generator develops over 20 inches Hg (mercury) of vacuum (10 psi). It is designed to run off of conventional shop air compressors delivering at least 65 psi at 3.5 SCFM. At 0 inches Hg it will evacuate 2.2 SCFM. The operating range is 40 psi - 100 psi.
30.99 USD

Vacuum bagging is a clamping system used for laminating a wide range of fabrics, core materials and veneers. It offers many advantages over conventional clamping. For repairs and composite construction, it uses atmospheric pressure to deliver firm even clamping pressure over the entire surface area, regardless of the type or quantity of material being laminated. By laminating over simple molds, composites can be molded into a wide range of functional shapes. #879 Release Fabric Economical Release Fabric is a tough, finely woven nylon fabric treated with a release agent. It is used to separate the absorber, breather and vacuum bag from the laminate in vacuum bagging operations. Excess epoxy bleeds through and is peeled from the cured laminate along with the Release Fabric. It's also used in hand lay-up applications to allow more squeegee pressure and protect the lay-up from contamination. Peels easily and leaves a smooth textured surface, ready for bonding or finishing. Not recommended for post-cure temperatures over 120 F (49 C). Available in 60" wide x 2 yd., and 10 yd. rolls; also in 60" x 9" sheets. #881 Breather Fabric Breather Fabric is a lightweight, polyester blanket that provides excellent air passage within the vacuum envelope while it absorbs excess epoxy. Available in 45" wide x 2.7 yd., and 10 yd. rolls. #882 Vacuum Bag Film Clear, heat-stabilized, modified nylon resin film. Can be used at temperatures up to 350 F (176 C) for typical composite cure cycle times. A tough, stretchable film for high vacuum pressures. Available in 60" wide x 2 yd., and 20 yd. rolls. #883 Vacuum Bag Sealant Mastic tape sealant for airtight seals between vacuum bags and molds. Easy to work around difficult angles, patching small leaks in the vacuum system. Available in 1/2" wide x 25' roll. #885 Vacuum Bagging Kit A complete starter kit for room temperature repairs and small laminating projects up to 13 square feet. The kit includes: 32-page manual on ''Advanced Vacuum Bagging Techniques.'' Instructions. Venturi vacuum generator. Vacuum cups. 1/4'' I.D. vacuum tubing (10'). Vacuum gauge. Junction ''T'' barbs (2). Release fabric (15 sq. ft.). Breather fabric (15 sq. ft.). Vacuum bag film (15 sq. ft.). Vacuum bag sealant (25 sq. ft.). The venturi generator develops over 20 inches Hg (mercury) of vacuum (10 psi). It is designed to run off of conventional shop air compressors delivering at least 65 psi at 3.5 SCFM. At 0 inches Hg it will evacuate 2.2 SCFM. The operating range is 40 psi - 100 psi.
19.99 USD

Vacuum bagging is a clamping system used for laminating a wide range of fabrics, core materials and veneers. It offers many advantages over conventional clamping. For repairs and composite construction, it uses atmospheric pressure to deliver firm even clamping pressure over the entire surface area, regardless of the type or quantity of material being laminated. By laminating over simple molds, composites can be molded into a wide range of functional shapes. #879 Release Fabric Economical Release Fabric is a tough, finely woven nylon fabric treated with a release agent. It is used to separate the absorber, breather and vacuum bag from the laminate in vacuum bagging operations. Excess epoxy bleeds through and is peeled from the cured laminate along with the Release Fabric. It's also used in hand lay-up applications to allow more squeegee pressure and protect the lay-up from contamination. Peels easily and leaves a smooth textured surface, ready for bonding or finishing. Not recommended for post-cure temperatures over 120 F (49 C). Available in 60" wide x 2 yd., and 10 yd. rolls; also in 60" x 9" sheets. #881 Breather Fabric Breather Fabric is a lightweight, polyester blanket that provides excellent air passage within the vacuum envelope while it absorbs excess epoxy. Available in 45" wide x 2.7 yd., and 10 yd. rolls. #882 Vacuum Bag Film Clear, heat-stabilized, modified nylon resin film. Can be used at temperatures up to 350 F (176 C) for typical composite cure cycle times. A tough, stretchable film for high vacuum pressures. Available in 60" wide x 2 yd., and 20 yd. rolls. #883 Vacuum Bag Sealant Mastic tape sealant for airtight seals between vacuum bags and molds. Easy to work around difficult angles, patching small leaks in the vacuum system. Available in 1/2" wide x 25' roll. #885 Vacuum Bagging Kit A complete starter kit for room temperature repairs and small laminating projects up to 13 square feet. The kit includes: 32-page manual on ''Advanced Vacuum Bagging Techniques.'' Instructions. Venturi vacuum generator. Vacuum cups. 1/4'' I.D. vacuum tubing (10'). Vacuum gauge. Junction ''T'' barbs (2). Release fabric (15 sq. ft.). Breather fabric (15 sq. ft.). Vacuum bag film (15 sq. ft.). Vacuum bag sealant (25 sq. ft.). The venturi generator develops over 20 inches Hg (mercury) of vacuum (10 psi). It is designed to run off of conventional shop air compressors delivering at least 65 psi at 3.5 SCFM. At 0 inches Hg it will evacuate 2.2 SCFM. The operating range is 40 psi - 100 psi.
142.99 USD

5" Universal Radar Dome Mount Fits - Furuno, Lowrance, Northstar, Raymarine and Garmin 2kW and 4kW Radar Domes
199.99 USD

Round Rail Mount Lever with Washer Replacement Parts for Magma grillsMagma Part #:10-043
9.49 USD

Offshore BBQ Rod Holder Mount Accessorize for your Outer Banks Stainless Marine BBQ grill.
39.99 USD

Electronics Mount for Raymarine & Humminbird Incorporate patented rubber balls that absorb vibration and shock to protect valuable delicate electronics. They install easily in areas with limited space and provide perfect viewing angles that are necessary for displays in bright marine environments. Life Time warrantyRAM-B-107-1 Light Duty Electronics Mount For Humminbird & Raytheon (For devices up to 2 lbs. 1" ball diameter.) Sh. Wt. 3 lbs.
34.99 USD